Archive for the ‘Energy’ Category
Where to locate emergency lighting in a commercial building. Part 3 of 3
Brought to you by lighting Denver at C and J Lighting.
Stairways: Stairways are a very important area for adequate lighting during an emergency or power outage. This is a great place to look for emergency lighting as most often it will be located here due to regulation and good common sense.
Steps & Ramps: In the same fashion as stairways, steps and ramps are places that also require lighting during an emergency or power outage to avoid injury from slip and falls.
Other businesses we recommend: Family counseling Denver Colorado at Affordable Counseling Connection, and causes of fibroids from Halt Medical.
Corridors, Junctions, & Hallways With Turns: Another great place to locate emergency lighting in a commercial building is down any type of corridor or hallway where the direction changes. Emergency lighting is needed to aim and illuminate the path of evacuation.
First Aid Stations & Fire Points: It is almost guaranteed that code regulations will require emergency lighting at these types of stations as it can become vitally important to locate a first aid or fire point during a power outage.
Escalators & Elevators: It is also a good bet that emergency lighting will be around escalators and elevators as this can reduce injury as escalators can be a major hazard during a power outage and these may also be on the path of evacuation.
Bathrooms: As these areas typically do not have windows due to the nature of the room itself, it is almost a guarantee there will be emergency lighting in these areas.
Heavy Machinery & Physical Risk: Another place there will usually be emergency lighting is anywhere there is a very real danger of physical injury. These types of areas will need to be clearly visible during an evacuation.
When attempting to find where to locate emergency lighting in a commercial building some research and common sense can go a long way.
Incoming search terms:
- cwqqtmvfqvt (1)
Saving energy have already stated by many people and many institutions in all of countries. Many companies have tried to use the advance of the technology to save the energy so that the energy can be complete the people’s need. one of the energy that should be saved is the saving of electric energy. The saving process can be started from the awareness of the people. For example, they can use the lamp that can save the electric energy. It is very practical for the people to save the energy because the lamp is one of the most important parts in people’s life.
In most of companies the lamp is one of sources that can be avoided. It needs much energy for the supply, so can the companies reduce the electric energy if they always use the lamp? The answer is yes. The companies can reduce the energy by using the lamp that can save the energy. Like in Ohio, the companies use the product of industrial lighting that can save the energy. The products of the industrial lighting are T5 and T8 lamps. It has been proof that the T5 and T8 can help the people in energy savings.
It is very effective for the people because by using the T5 and T8 the people can reduce their energy till 60%. The people also can save their energy costs for about 50%. It is very benefit for the people because it has lasting longer than other lamps. These lamps also do not get warm faster than other. The retrofit company gives the best quality of its lamps to the people. You can check it in Roi-energy.com to get the further information about these safe lamps. By using the T5 and T8 now, automatically you will start to save your energy and your bill.
Just like solar energy, wind energy is another environment-friendly and economical energy source. With almost 40% of wind energy sources of Europe in the United Kingdom, there is immense potential to use wind energy as a source of energy.
Generating power through wind is not only efficient but also renewable like solar energy. The only downside is that a tall, moderately sized generator can be a sore eye and spoil the visual landscape, leading to murmurs of disapproval among neighbours. Think about this before you go ahead and think about how to generate wind energy in your area. However, if you do not live in a very populated area and your neighbors consent to your wind energy project, there could be nothing more beneficial to harness the potential of such a natural and renewable resource called wind.
Getting Help in the Start
If you are wondering how to generate wind energy, the British Wind Energy Association or BWEA is a good professional source of services and information for initiating projects related to wind energy. This professional body continuously organizes and manages several initiatives to propagate the use of wind as a source of energy across the country and its residences. It has information on local suppliers of wind systems and information on grants and permissions.
The ‘Energy Saving Trust’ which is backed by the government also provides provide advice on several issues for both companies and individuals and companies desiring to install wind generators on a small scale.
Other Practicalities like Cost and Savings
The cost of wind generators should fall in the range of 3000 pounds -15000 pounds for each kilowatt. This is as competitive as solar and actually slightly cheap when compared to the high output it generates. It is also expected to generate higher output in a year compared to its output in the previous year. Your wind generator should break even in about five years and the way the prices of normal energy sources are increasing, the returns of a wind generator will surely increase over a period of time.
How to Position Your Turbine
It is best to place the turbine high if you want to get the most of the wind strength without any obstructions. Also make sure to measure the wind strength in your locality so that you can place the turbine facing the direction where the wind is prevailing. To measure the wind strength, you can either buy or hire an anemometer. You can also get the person installing your wind generator to do that.
Battery or Grid?
A battery can be connected to wind generators of small scale to provide electricity to your house. The other option is to connect the wind generator to the National Grid. The decision to do the former or the latter depends totally on the circumstance. As such there is no major difference except that it will affect the direction of your energy. If you happen to stay in an area that is remote with no access to the National Grid, energy should then be directed to the battery which in turn will be connected to your residence’s mains. If you can easily access the National Grid, get the generator connected to the grid. By connecting to the grid not only will you be benefited from power savings by not using the supply of electricity from the grid, you will also be able to sell surplus electricity to the grid.
Read the whole ebook - Home Made Energy
Energy deregulation has led to numerous alternatives for consumers. They have the freedom in order to select the energy company they require, this is why more consumers transfer from one supplier to another. Individuals think that they might be in a position so as to save money on their monthly energy bills and thus they do so. There might be further cause behind the transferring of customers to but the major reason might be because of the services the company provides.
Transferring in order to a different energy supplier is a tough task unless, you have got all the required information concerning every single choice provided in the market. Its a good thing that the trouble of transferring to your preferred energy supplier is resolved by the electricity comparison web sites.
The clients are being provided by the websites with the essential information in the form of evaluation of the energy rates and contract information granted that the questions asked were entered correctly. The comparison you acquire from the websites is reliant to the accuracy of the information you entered. A great benefit of these web-sites is that they could give you with the fastest energy comparison which would have taken plenty of your time if you’ve done that manually. As a result they do not only give you the comparison between the various rates offered in the market but it even spared you from the extra effort of checking out numerous web sites so as to acquire the necessary comparison on electricity rates.
Changes in rates are essential aspects of the agreement presented by various energy supplying companies. There are certain companies where you obtain a 6 month deal and before long you got in order to know that its charge has increased in order to a notable point. The greatest way so as to be well-versed about the modifications in rate is so as to constantly visit the web-sites in order to keep posted about the numerous updates on the contract. It is generally a quick process and it would only take few minutes so as to provide you the essential information you require.
One more advantage of these web sites is when you are in a rush of switching in order to a different energy supplier for the reason that your present contributor is not satisfying your needs in a precise manner. There might be a possibility of transferring for a different supplier for the reason that you must move in in order to another place where you would find some good rates so as to save on your electricity bills or some other explanations which may direct you so as to the emergency transferring. It does not matter what the reason is, these web sites could be the greatest means for you to move about in in order to the right path.
Incoming search terms:
Right now, there are a few things you can do around your home to air seal it to save money during the winter months and during the summer.
As mentioned in Part 1, your home is a “thermal envelope”. That is the sum total of the home’s insulation systems: walls, ceilings, foundation, floors, windows, and doors. These work more effectively with good, tight fits that seal out the weather and air. By having a tight seal on your home’s thermal envelope, the less energy you waste or lose by exchanging it too often with the air outside.
Now, we’re going to look at exterior doors, the laundry center, the water heater tank, HVAC (Heating, Ventilation, and Air Conditioning), attic insulation, attic ventilation and rain gutters.
Presenting The Doors!
We all want our doors to be attractive, secure, and weather proof. Like windows, when they are properly installed and kept in good condition, they can save you energy and money. If your door is hard to close or open, moves the whole door frame when you open or close the door, rattles when it is closed, or you see daylight and feel a draft coming from around it, then your door needs work.
When a door doesn’t close correctly, it obviously fails to seal. If your exterior door is difficult to open or close, the first thing to look for is if something is caught in the door or if something is sticking out from the door frame, such as a screw head not fully tightened against the hinge. Next, determine with a carpenter’s level whether the door is hanging plumb (straight up and down) and if the door jambs are parallel to each other. Sometimes, a screw head not tightened into the hinge can prevent a door from closing properly and over time deform and loosen the door frame or the door. Also, check to see if any hinges move toward or away from the door jamb or if they wiggle. Hinges should be tightly fastened to the door and the door jamb with no other movement except at the hinge joint.
Once I lived in an old house and the back door was hard to close because the whole frame moved with it. It was one of those things I kept putting off to fix. Then one night, I pulled the door shut so hard that I pulled the entire door and door frame out from the wall of the house. I tacked it back in place for the night but the next morning, I settled down to repair it. The original nails had rusted down to the thickness of thread while the wooden shims that kept the door seated properly had rotted because moisture got inside the door frame.
If your door frame moves when you open or close the door, don’t put it off repairing it like I did. Fix it now. First, remove the casing from both the inside of the door and the exterior. Be careful – often in older homes, door casing and other moldings are unique or are no longer available. Sharp-edged casing pry bars are perfect for this. With a little patience and care, you can remove the casing without damaging it too much. A putty knife and a claw hammer are also useful. Again, be patient and careful – you are disassembling not destroying.
After you remove the casing, look for any damage to the wood making up the door frame; such as if it is rotten or split. Check to see if the shims are in place and intact. If everything looks right, check the frame to see if it is plumb. Add shims as needed and check that the door opens and closes correctly. Usually, it is easier to tack a scrap 1? × 2? across the door when it’s closed to seat the door frame properly. When it’s plumb and shimmed, carefully nail the frame into place. Next, vacuum debris from the area and seal up seams and gaps with either caulk or expanding foam. Re-fasten the casing and cover up the old nail holes with color-matched wood putty.
If you can close a kleenex in your door and then pull it out easily or if your door rattles from noise or the wind, it means it’s just not seated snuggly. The easiest starting place to for this fix is to add weather stripping. Usually, doors made over the past 25 years have had weather stripping built onto them. But being a door is rough work. Over time, the weather stripping gets stripped from the door. In some cases, the same weather stripping types are still used by the door manufacturer and can be easily replaced. Usually with much older homes, it’s not the case. You’ll be either replacing worn-out weather stripping someone else applied, or you’ll be putting on brand new.
First, measure the gap between the door surface and the door jamb at several places. Add about 1/16 of an inch to this measurement and this will give you a rough thickness of the self-adhesive foam or felt you will need to apply. Typically, I apply the foam stripping to the door jamb. Since the door jamb doesn’t go anywhere there’s less of a chance for something bumping against it and tearing off the foam. The door, on the other hand, is meant to move and will encounter all sort of things in its travels. As mentioned, you want the door to close firmly. Be sure to buy more foam than you will need so you can add and adjust the foam until you have a good seal.
If your door is in too bad of condition to repair, then it really is no longer a matter of weatherization but security. Seriously consider replacing it. Residential exterior doors come in three standard widths: 30, 32, and 36 inches.
Generally, the most insulating material for an exterior door is wood because it doesn’t conduct heat as easily as metal, vinyl, or fiberglass. That being said, most inexpensive wooden doors don’t fare well over time. They wear quickly in the areas that have the most contact (door handles and foot area), their mounting screws can loosen or tear, and depending on the harshness of the weather they can dry out and split. Steel doors provide better security and stand up to wear but they conduct heat. Wood-core steel doors and foam core doors last longer, are stronger, and better insulated. Fiberglass doors usually are the most strong, durable, and well insulating but tend to be more expensive.
Door Sweeps and Door Jambs with Vinyl Weather-stripping
A door’s most drafty area is along the bottom where it meets the door threshold. Most thresholds are aluminum or wooden ridges that meet the bottom of the door and form a seal. However, since the door is constantly being opened and the threshold is being stepped on, the factory-installed weatherization can wear out quickly. It can be quickly and easily replaced with a self-adhesive vinyl strip that hangs down from the bottom edge of the door. You attach it on the interior side of the door.
There is another kind of door sweep that uses multiple vinyl strips to block drafts. Somewhat more expensive, but it slips on over the bottom edge of the door and is held on with screws.
One product I have used with great success is pvc door jambs with built-in vinyl weather stripping. Mounted on the outside of your door, these door jambs can either replace your existing jambs or slide over them. The vinyl weather-stripping can be pushed up snugly against the door to keep out drafts when the door is closed. Use a circular miter saw to make the proper angled cuts so they can be mounted attractively in place. When they are in position, they can be quickly nailed or screwed into place and then painted. While I like these, there are many other similar kits that might be more suitable for your particular job.
The Laundry Center
The big energy users in the laundry area are the washer and the dryer. The typical washer uses about 0.256 kWh per load. The main cost is obviously the amount of hot water the is used during each load. Top loading washers use up to 40 gallons while front loaders use 10-24 gallons. It is easy to cut costs here by washing in warm or cold water. However, the main energy savings comes from drying your clothes. Even though modern washing machines do an excellent job of extracting the water from clothes by spinning them, they still need to be dried.
Dryers tend not to be very energy efficient because they have one job: force dry, heated air into a rotating drum to evaporate water. Dryers use ten to fifteen percent of domestic energy in the United States. Dryers also cause lint. Lint comes from fibers in your clothing coming loose as the clothes tumble across each other in a dryer’s hot drum. Lint not only collects in your dryer’s lint trap but also through the dryer’s duct work. If lint begins to obstruct or clog your dryer’s duct work, the evaporated water from your nice, clean clothes will not leave the system. If the water is trapped, it will take longer and longer for the dryer to work. Therefore, once a year, pull your dryer away from the wall, detach the duct from the bottom of your dryer, and pull out as much lint as you can from the dryer and the duct. The first time you do this, you might be surprised how much you pull out. You’ll also notice a big improvement in the time it takes for your dryer to dry your clothes.
During the cooler winter months when you are heating your home, you may notice your home feeling drier. While not always a bad thing, if your skin feels dry and itchy or if you notice your sinuses feeling raw and irritated more often, maybe your home is too dry. One way around this is to disconnect your dryer vent tubing from the duct work leading out of the house. Place a nylon sock over the end of the vent tubing and tie it in place with a long twist tie or rubber band. (Make sure you block up the vent going outside). This way, every time you run your drier, you will heat and humidify your house too.
Hanging your clothes not only save energy but also helps them last longer. Dry your clothes on a drying rack or clothes line. If you can’t hang them outside, you can hang them inside by buying a
Becoming an energy broker will be a great choice for any person searching for a creative way to earn some extra cash. This is because you are principally in the business for yourself, but not by yourself. You could work when you desire to, as much as you will want to, as frequently as you will like to and you can work at your own pace, depending on your economical target. As an energy broker you have the possibility to make a profit of 5 to 7 figures. These days, almost everybody in the world has electricity. In many states, no more than 5 to 10% of individuals have made the switch to an outside suppliers of electricity, so as an energy broker the market is flourishing with prospects to make a enormous profits.
You don’t need to be a talented salesperson to become an excellent energy broker, this is because you are not selling something or anything, you are just telling individuals how to save money on a bill that they will have to pay in any case.
If you desire to become an energy broker, the primary thing you must become aware of is that they work in a service industry and as such, the customer is regarded as V.I.P. and not just some other caller. So you’ll frequently discover that a customer’s call would be responded immediately by the company and isn’t directed to a call center. Customers are to be expected to talk straight away to a committed business energy specialist.
Then the agent would be able to give information about the procedure directly to the customer. As an energy broker you are most probably to present various forms of market analysis and update your client about the up to date trend in energy charges. You will then suggest extra services and resolution to help your customer trim down their energy expenses, or control their energy costs better.
So becoming an Energy Broker is an excellent option if you truly wish to make your own financial destiny. There are numerous contractors you could work for but keep this in mind, most of them charge a very expensive amount of fee for you to become an Energy Broker; if truth be told, hundreds of dollars are being charged by several external suppliers in addition to the current monthly fees which you need to pay. Keep in mind that you don’t need to pay a company, for you to become an energy broker.
Becoming an Energy Broker is a wonderful choice and selecting an excellent company to be related to is another clever choice.
Incoming search terms:
- energy broker (1)
As we all know, Texas summers can be brutally hot, and Texas winters can be surprisingly cold. Both seasons end up wreaking havoc on our utility bills as we struggle to keep our homes cool in the summer and warm in the winter. Add in all the other little things — the coffee maker, the computer, the TV, and all the other devices that spend most of their time plugged into your home’s electrical system — and many homeowners give up on ever finding a way to really control their Texas electricity costs. But as energy prices continue to rise, and as the pressures on the average homeowner’s finances rise right along with them, the need to find new ways to cut costs and save money becomes a lot more compelling. We know that we could probably cut back on our energy usage, but how do we know where to start? Our Texas electric bill tells us how much energy we’ve used, but only once a month, and that’s not very helpful. Even when we make changes, it could take months to tell whether they’re working, or if they’re saving us enough to be worthwhile. At the same time, major sources of inefficiency might be going unnoticed and unaddressed.
Two competing new services, PowerMeter by Google and Hohm by Microsoft, are on the way with some new tools to help Texas homeowners. Microsoft estimates that the average American home could save almost 0 per year on energy usage. While that number sounds big, they base it on extensive testing in 60 million homes across the country; and of all 50 states, Texas ranked lowest in energy efficiency. Of course, what that really means is that Texas potentially has the biggest opportunity to use less electricity, reduce our carbon footprint, and save a whole lot of money.
Both PowerMeter and Hohm promise the potential for big increases in both efficiency and cost savings by way of an energy monitoring device called a smart meter. Once connected to your home’s electricity supply system, the meter sends an ongoing stream of data to your home computer via a connected wireless device. Your computer then sends that information on to a data hub run by one of the two companies. There, your information is analyzed and re-packaged into a dynamic, user-friendly web interface for you to review and use.
The appeal of these applications for homeowners is that your energy usage is no longer reduced to a single, inscrutable number on your monthly utility bill. The two applications differ somewhat in how your utility data is presented, but the primary feature in both is an extensive analysis of exactly how all of that electricity is being used. For example, Google PowerMeter can help you identify how much energy you’re using on a constant basis — the low-level drain from “always on” devices that can, over time, add up to a major source of inefficiency. Microsoft’s Hohm goes a step further by making active recommendations about how a homeowner might cut back their electricity usage, increasing energy efficiency and lowering costs.
There are further differences between the two services. Google’s emphasis is on the numbers; it tells you exactly how much power you’re using on an hourly basis, and generates graphs of usage over time, whether that means the last hour or the last month. This is a great service for people who like their data raw, as it means that a homeowner can correlate usage to specific patterns during the day. For example, if you know your usage spikes around 7 AM, you can probably guess that it has a lot to do with your family getting ready for work and school. Therefore, you might be able to save money if everyone takes shorter showers, or if you lower the temperature on your water heater. PowerMeter can also analyze usage patterns over the past to predict what your approximate usage and costs will be in the future. So as you make changes and check your results, you can watch your projected bills rise and fall until you’re happy with them.
Microsoft Hohm, on the other hand, is staking its claim on reaching the masses. Already available nationwide, Hohm’s interface is a a more comfortable affair, replacing a lot of the hard, granular data with a condensed “Hohm Score” that compares your home’s real energy usage to its potential energy efficiency — that is, how much you’re actually saving versus how much you could potentially be saving. It also guides you toward possible sources of savings, ranging from large and potentially savings-rich projects like insulating your home, to small things like replacing conventional light bulbs with power-saving compact fluorescent bulbs. It also allows you to compare your energy usage to that of people in your neighborhood, city, state, and all across the country.
If you’re interested in monitoring your home’s energy usage, there are a few things to keep in mind, since the two applications work a bit differently. So far, Google PowerMeter forms its main partnerships with utility companies, and to date it hasn’t established such a relationship with any Texas energy company, so for the time being it remains out of reach for Texans. However, if you’re interested in PowerMeter, it’s worth keeping in mind that while Google is sometimes a bit coy in the beginning, when they do enter a market, they often take it over completely. Google also has an excellent reputation for development, and loves to give its users exactly what they want. While PowerMeter might not yet be a player in your area, they could become the biggest game in town in the reasonably near future.
Microsoft Hohm, on the other hand, partners primarily with device-makers rather than power companies. Anyone can buy and install a compatible device and be up and running, no matter where they live or who supplies their energy. But Hohm requires more of a time investment to reach its full potential. A new user of the service will start out by answering a substantial number of questions about their home — details about the building, what kind of appliances you use, etc. — and some homeowners may find the process a little daunting. (Apartment dwellers may even find Hohm to be of limited use to them if they don’t have ready access to some of these details.) The good news is, even a partially-completed profile can produce some very useful insights and advice, and you can always add information and refine your profile later on.
If you’re interested in using Microsoft Hohm, your first step should be to contact your energy provider and ask them for any relevant information they can provide. Then purchase a Hohm-compatible device, such as Blue Line’s Power Cost Monitor, and register for your free Hohm account. Texas homeowners leaning towards Google’s PowerMeter service will have to wait a while longer, but in the meantime, you should contact your energy provider and let them know that you want to see a Texas energy company on PowerMeter’s list of partners.
In the end, it’s worth bearing in mind that both services are currently in their nascence, and will doubtless see further development and lots of changes in the future. As smart meters become more common and the cost of energy goes up, homeowners will do well to find a way to make use of the information that a these new monitoring tools can provide. Google and Microsoft are already working to make this information easily accessible to their users, and the competition between them will undoubtedly bring out the best in both.
There’s a lot of money to be saved on energy usage in this country, and perhaps nowhere more than in Texas. To help you make sure that some of that money ends up in your pocket, Google PowerMeter and Microsoft Hohm offer two great ways to discover your home’s potential for energy savings, and make your home the most efficient house on the block.
Energy Costs Affecting Business Owners
Energy costs have risen globally, threatening the growth of businesses everywhere. Some of the hardest-hit organizations are those that own or lease property and pay for electricity. According to the U.S. Green Building Council, buildings account for 36 percent of total energy use and 65 percent of electricity consumption. So, when electrical energy costs rise, businesses demand a solution. Energy Automation Systems, Inc. (EASI), an international leader in energy-saving technology, can reduce energy costs by reducing the electrical energy waste and consumption already present in your facility today.
A Real Solution
Energy Automation Systems Inc. (EASI) designs, manufactures and installs systems that reduce electrical energy consumption and improve power quality in commercial and industrial facilities by enhancing the efficiency of electrical systems with no trade off in performance. Energy Automation Systems work passively, requiring no routine maintenance, and they function in virtually any facility that consumes electricity. The company’s proven systems can reduce a facility’s electrical energy consumption by 30% or more – and your savings are backed by a written guarantee, underwritten by a major insurance company.
Energy Automation Systems has installed customized energy conservation systems for decades for many thousands of clients in more than 60 countries around the world. Energy Automation Systems Founder and CEO Joseph Merlo has more than 30 years of experience in the energy conservation business and has helped countless companies reduce their energy costs. Paul Bleiweis, President of Energy Automation Systems, leads development of the company’s unique portfolio of energy-saving products. As a result of their leadership, Energy Automation Systems clients have included General Electric, British Petroleum, Apollo Management, Saudi Arabia Basic Industries Corporation (SABIC) and ConAgra Foods, as well as many other companies, large and small.
If your business is looking for a long-term solution to rising energy costs, visit the company’s corporate Web site at: www.energyautomation.com. If you would like to learn more about the company’s executive leadership, click here for a bio on Joseph Merlo and Paul Bleiweis.
A Unique Opportunity
As a result of rising energy costs, demand for Energy Automation Systems Inc. (EASI) systems is growing around the world. For years the company provided its systems directly to customers, but increasing demand lead the company to develop a unique business opportunity in which individuals can become Affiliates of the company and market its products to customers around the world.
For a brief overview of the Energy Automation Systems business opportunity, visit www.energysavingbusiness.com.
For an in-depth look at the Energy Automation Systems opportunity, including video interviews with current Energy Automation Systems Affiliates and customers and a detailed overview of Energy Automation Systems product portfolio, visit www.easibusiness.com.